ELISA Kit for Y-Box Binding Protein 1 (YBX1)

BP8; CSDA2; CSDB; DBPB; MDR-NF1; NSEP1; YB1; Nuclease Sensitive Element Binding Protein 1; CCAAT-binding transcription factor I subunit A; DNA-binding protein B

FOR IN VITRO AND RESEARCH USE ONLY, NOT FOR USE IN CLINICAL DIAGNOSTIC PROCEDURES!
  • ELISA Kit for Y-Box Binding Protein 1 (YBX1)Packages (Simulation)
  • ELISA Kit for Y-Box Binding Protein 1 (YBX1)Packages (Simulation)
  • ELISA Kit for Y-Box Binding Protein 1 (YBX1)Results demonstration
  • SEC609Hu.jpgTypical Standard Curve
  • CertificateISO9001: 2008, ISO13485: 2003 Registered

Specificity

This assay has high sensitivity and excellent specificity for detection of Y-Box Binding Protein 1 (YBX1).
No significant cross-reactivity or interference between Y-Box Binding Protein 1 (YBX1) and analogues was observed.

Precision

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Y-Box Binding Protein 1 (YBX1) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Y-Box Binding Protein 1 (YBX1) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Reagents and materials provided

ReagentsQuantityReagentsQuantity
Pre-coated, ready to use 96-well strip plate1Plate sealer for 96 wells4
Standard2Standard Diluent1×20mL
Detection Reagent A1×120µLAssay Diluent A1×12mL
Detection Reagent B1×120µLAssay Diluent B1×12mL
TMB Substrate1×9mLStop Solution1×6mL
Wash Buffer (30 × concentrate)1×20mLInstruction manual1

Assay procedure summary

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.

ELISA Kit for Y-Box Binding Protein 1 (YBX1)

Test principle

The test principle applied in this kit is Sandwich enzyme immunoassay. The microtiter plate provided in this kit has been pre-coated with an antibody specific to Y-Box Binding Protein 1 (YBX1). Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated antibody specific to Y-Box Binding Protein 1 (YBX1). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. After TMB substrate solution is added, only those wells that contain Y-Box Binding Protein 1 (YBX1), biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450nm ± 10nm. The concentration of Y-Box Binding Protein 1 (YBX1) in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Related products

Catalog No.Organism species: Homo sapiens (Human)Applications
RPC609Hu01Recombinant Y-Box Binding Protein 1 (YBX1)Positive Control; Immunogen; SDS-PAGE; WB.
PAC609Hu01Polyclonal Antibody to Y-Box Binding Protein 1 (YBX1)WB; IHC; ICC; IP.
MAC609Hu21Monoclonal Antibody to Y-Box Binding Protein 1 (YBX1)WB; IHC; ICC; IP.
SEC609HuELISA Kit for Y-Box Binding Protein 1 (YBX1)Enzyme-linked immunosorbent assay for Antigen Detection.
GUESTBOOK