ELISA Kit for Amiloride Binding Protein 1 (ABP1)

AOC1; DAO; KAO; Histaminase; Kidney amine oxidase; Diamine Oxidase; Amiloride-sensitive amine oxidase; Amine oxidase copper domain-containing protein 1

  • ELISA Kit for Amiloride Binding Protein 1 (ABP1) Packages (Simulation)
  • ELISA Kit for Amiloride Binding Protein 1 (ABP1) Packages (Simulation)
  • ELISA Kit for Amiloride Binding Protein 1 (ABP1) Results demonstration
  • SEA656Ra.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

This assay has high sensitivity and excellent specificity for detection of Amiloride Binding Protein 1 (ABP1).
No significant cross-reactivity or interference between Amiloride Binding Protein 1 (ABP1) and analogues was observed.

Recovery of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

Matrices listed below were spiked with certain level of recombinant Amiloride Binding Protein 1 (ABP1) and the recovery rates were calculated by comparing the measured value to the expected amount of Amiloride Binding Protein 1 (ABP1) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 82-89 86
EDTA plasma(n=5) 78-101 95
heparin plasma(n=5) 85-103 93

Precision of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Amiloride Binding Protein 1 (ABP1) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Amiloride Binding Protein 1 (ABP1) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Amiloride Binding Protein 1 (ABP1) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 80-90% 81-99% 93-101% 91-105%
EDTA plasma(n=5) 94-102% 83-94% 81-97% 92-101%
heparin plasma(n=5) 93-102% 95-102% 87-101% 86-94%

Stability of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.

Test principle of the ELISA Kit for Amiloride Binding Protein 1 (ABP1)

The test principle applied in this kit is Sandwich enzyme immunoassay. The microtiter plate provided in this kit has been pre-coated with an antibody specific to Amiloride Binding Protein 1 (ABP1). Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated antibody specific to Amiloride Binding Protein 1 (ABP1). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. After TMB substrate solution is added, only those wells that contain Amiloride Binding Protein 1 (ABP1), biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450nm ± 10nm. The concentration of Amiloride Binding Protein 1 (ABP1) in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Related products

Catalog No. Organism species: Rattus norvegicus (Rat) Applications (RESEARCH USE ONLY!)
RPA656Ra02 Recombinant Amiloride Binding Protein 1 (ABP1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA656Ra01 Recombinant Amiloride Binding Protein 1 (ABP1) Positive Control; Immunogen; SDS-PAGE; WB.
PAA656Ra02 Polyclonal Antibody to Amiloride Binding Protein 1 (ABP1) WB; IHC; ICC; IP.
PAA656Ra01 Polyclonal Antibody to Amiloride Binding Protein 1 (ABP1) WB; IHC; ICC; IP.
LAA656Ra71 Biotin-Linked Polyclonal Antibody to Amiloride Binding Protein 1 (ABP1) WB; IHC; ICC.
MAA656Ra22 Monoclonal Antibody to Amiloride Binding Protein 1 (ABP1) WB; IHC; ICC; IP.
MAA656Ra21 Monoclonal Antibody to Amiloride Binding Protein 1 (ABP1) WB; IHC; ICC; IP.
SEA656Ra ELISA Kit for Amiloride Binding Protein 1 (ABP1) Enzyme-linked immunosorbent assay for Antigen Detection.
LMA656Ra Multiplex Assay Kit for Amiloride Binding Protein 1 (ABP1) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK