ELISA Kit for Aquaporin 4 (AQP4)

HMIWC2; MIWC; WCH4; Mercurial-insensitive water channel

  • ELISA Kit for Aquaporin 4 (AQP4)Packages (Simulation)
  • ELISA Kit for Aquaporin 4 (AQP4)Packages (Simulation)
  • ELISA Kit for Aquaporin 4 (AQP4)Results demonstration
  • SEA582Hu.jpgTypical Standard Curve
  • CertificateISO9001: 2008, ISO13485: 2003 Registered


This assay has high sensitivity and excellent specificity for detection of Aquaporin 4 (AQP4).
No significant cross-reactivity or interference between Aquaporin 4 (AQP4) and analogues was observed.


Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Aquaporin 4 (AQP4) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Aquaporin 4 (AQP4) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%


The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Reagents and materials provided

Pre-coated, ready to use 96-well strip plate1Plate sealer for 96 wells4
Standard2Standard Diluent1×20mL
Detection Reagent A1×120µLAssay Diluent A1×12mL
Detection Reagent B1×120µLAssay Diluent B1×12mL
TMB Substrate1×9mLStop Solution1×6mL
Wash Buffer (30 × concentrate)1×20mLInstruction manual1

Assay procedure summary

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.

ELISA Kit for Aquaporin 4 (AQP4)

Test principle

The test principle applied in this kit is Sandwich enzyme immunoassay. The microtiter plate provided in this kit has been pre-coated with an antibody specific to Aquaporin 4 (AQP4). Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated antibody specific to Aquaporin 4 (AQP4). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. After TMB substrate solution is added, only those wells that contain Aquaporin 4 (AQP4), biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450nm ± 10nm. The concentration of Aquaporin 4 (AQP4) in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Related products

Catalog No.Organism species: Homo sapiens (Human)Applications
RPA582Hu01Recombinant Aquaporin 4 (AQP4)Positive Control; Immunogen; SDS-PAGE; WB.
PAA582Hu01Polyclonal Antibody to Aquaporin 4 (AQP4)WB; IHC; ICC; IP.
MAA582Hu22Monoclonal Antibody to Aquaporin 4 (AQP4)WB; IHC; ICC; IP.
MAA582Hu21Monoclonal Antibody to Aquaporin 4 (AQP4)WB; IHC; ICC; IP.
LAA582Hu72Biotin-Linked Monoclonal Antibody to Aquaporin 4 (AQP4)WB; IHC; ICC.
SEA582HuELISA Kit for Aquaporin 4 (AQP4)Enzyme-linked immunosorbent assay for Antigen Detection.
PSA582Hu01Antibody Pair for Aquaporin 4 (AQP4)ELISA; CLIA; ELISPOT; Luminex; Immunochromatography and other Immunoassays.
KSA582Hu01ELISA Kit DIY Materials for Aquaporin 4 (AQP4)Main materials for "Do It (ELISA Kit) Yourself".