CLIA Kit for Concanavalin A (ConA)

Con-A

  • CLIA Kit for Concanavalin A (ConA) Packages (Simulation)
  • CLIA Kit for Concanavalin A (ConA) Packages (Simulation)
  • CLIA Kit for Concanavalin A (ConA) Results demonstration
  • SCC179Ge.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Concanavalin A (ConA)

This assay has high sensitivity and excellent specificity for detection of Concanavalin A (ConA).
No significant cross-reactivity or interference between Concanavalin A (ConA) and analogues was observed.

Precision of the CLIA Kit for Concanavalin A (ConA)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Concanavalin A (ConA) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Concanavalin A (ConA) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Concanavalin A (ConA)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Concanavalin A (ConA)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Concanavalin A (ConA)

The microplate provided in this kit has been pre-coated with an antibody specific to Concanavalin A (ConA). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Concanavalin A (ConA). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Concanavalin A (ConA) level in the sample or standard.;

Related products

Catalog No. Organism species: Pan-species (General) Applications (RESEARCH USE ONLY!)
PAC179Ge01 Polyclonal Antibody to Concanavalin A (ConA) WB; IHC; ICC; IP.
LAC179Ge71 Biotin-Linked Polyclonal Antibody to Concanavalin A (ConA) WB; IHC; ICC.
SEC179Ge ELISA Kit for Concanavalin A (ConA) Enzyme-linked immunosorbent assay for Antigen Detection.
SCC179Ge CLIA Kit for Concanavalin A (ConA) Chemiluminescent immunoassay for Antigen Detection.
LMC179Ge Multiplex Assay Kit for Concanavalin A (ConA) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
PSC179Ge01 Antibody Pair for Concanavalin A (ConA) ELISA; CLIA; ELISPOT; Luminex; Immunochromatography and other Immunoassays.
KSC179Ge01 ELISA Kit DIY Materials for Concanavalin A (ConA) Main materials for "Do It (ELISA Kit) Yourself".
GUESTBOOK