CLIA Kit for Calcitroic Acid (CA)
- Product No.CCO007Ge
- Organism SpeciesPan-species (General) Same name, Different species.
- Test MethodCompetitive Inhibition
- Assay Length2h
- Detection Range195.3-50,000pg/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 75.1pg/mL.
- Sample TypeBiological agents
- Download Instruction Manual
- UOM 48T96T 96T*5 96T*10 96T*100
-
FOB
US$ 571
For more details, please contact local distributors!US$ 816
For more details, please contact local distributors! US$ 3672
For more details, please contact local distributors! US$ 6936
For more details, please contact local distributors! US$ 57120
For more details, please contact local distributors!
-
Packages (Simulation)
-
Packages (Simulation)
-
Results demonstration
-
Typical Standard Curve
-
ISO9001: 2008, ISO13485: 2003 Registered
Specificity of the CLIA Kit for Calcitroic Acid (CA)
This assay has high sensitivity and excellent specificity for detection of Calcitroic Acid (CA).
No significant cross-reactivity or interference between Calcitroic Acid (CA) and analogues was observed.
Precision of the CLIA Kit for Calcitroic Acid (CA)
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Calcitroic Acid (CA) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Calcitroic Acid (CA) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%
Stability of the CLIA Kit for Calcitroic Acid (CA)
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Assay procedure summary of the CLIA Kit for Calcitroic Acid (CA)
1. Prepare all reagents, samples and standards;
2. Add 50µL standard or sample to each well.
And then add 50µL prepared Detection Reagent A immediately.
Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
7. Read RLU value immediately.
Test principle of the CLIA Kit for Calcitroic Acid (CA)
The microplate provided in this kit has been pre-coated with a monoclonal antibody specific to Calcitroic Acid (CA). A competitive inhibition reaction is launched between biotin labeled Calcitroic Acid (CA) and unlabeled Calcitroic Acid (CA) (Standards or samples) with the pre-coated antibody specific to Calcitroic Acid (CA). After incubation the unbound conjugate is washed off. Next, avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. The amount of bound HRP conjugate is reverse proportional to the concentration of Calcitroic Acid (CA) in the sample. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is reverse proportional to the Calcitroic Acid (CA) level in the sample or standard.
GIVEAWAYS
INCREMENT SERVICES
Related products
| Catalog No. | Organism species: Pan-species (General) | Applications (RESEARCH USE ONLY!) |
| CCO007Ge | CLIA Kit for Calcitroic Acid (CA) | Chemiluminescent immunoassay for Antigen Detection. |